Search found 38 matches
- Thu Jan 18, 2024 4:30 pm
- Forum: Engine Tech
- Topic: Lets talk about intake gaskets . . . . .
- Replies: 40
- Views: 66594
Re: Lets talk about intake gaskets . . . . .
I've seen some heads where someone took a vary small centre punch and put little dimples around the intake ports....the bottom of the port and top and down the centre wall....I assume trying ti hold the gasket better....
- Fri Aug 25, 2023 7:54 am
- Forum: Engine Tech
- Topic: Cam grinding who is best & Price
- Replies: 23
- Views: 3431
Re: Cam grinding who is best & Price
I had Mike Jones regrind a mechanical roller camshaft for me, great service, great workmanship.
Super to deal with.
Super to deal with.
- Fri Aug 25, 2023 7:43 am
- Forum: Engine Tech
- Topic: Spark Plugs
- Replies: 2
- Views: 474
Re: Spark Plugs
Thanks, yes you are correct its a 14mm x 0.750" reach plug with gasket seal. I was asking for a friend who called me.
- Thu Aug 24, 2023 9:10 pm
- Forum: Engine Tech
- Topic: Spark Plugs
- Replies: 2
- Views: 474
Spark Plugs
Hey Folks,
What spark plug is recommended for ZZ350 aluminum heads, part# 14096217
Not so worried about heat range just the correct plug for length, we can figure out the heat range once I get the correct plug.
Thanks.
What spark plug is recommended for ZZ350 aluminum heads, part# 14096217
Not so worried about heat range just the correct plug for length, we can figure out the heat range once I get the correct plug.
Thanks.
- Sat Jan 07, 2023 1:06 pm
- Forum: Engine Tech
- Topic: FelPro Head Gaskets
- Replies: 6
- Views: 552
FelPro Head Gaskets
Hello, I have a .060 bored 350 block, stock stroke at 3.480", -10 Brodix CNC ported heads, mechanical roller cam, 12.5:1 compression ratio. My question is....I have a set of 1043 head gaskets and also a set of 1003 head gaskets.....I see the 1043 gasket is recommended for race heads.....what is...
- Tue Dec 20, 2022 5:58 am
- Forum: Engine Tech
- Topic: 2 piece Rear Main Seal for SBC
- Replies: 16
- Views: 1392
2 piece Rear Main Seal for SBC
Just a quick question, does anyone have the Felpro part number for the 2 piece rear main seal for a SBC that has been line bored?
- Wed Jan 26, 2022 8:54 am
- Forum: Engine Tech
- Topic: Fatal Mistakes....
- Replies: 154
- Views: 62905
Re: Fatal Mistakes....
Well here it goes.... a few fatal mistakes and a good laugh! 1. In about 1975 my brother and I were into anything engines we were 15 and 16...(Our Dad was a Heavy Duty Equipment Technician and was always building dune Buggies or engines or something in our backyard garage). Anyway my brother and I h...
- Tue Jun 22, 2021 9:51 am
- Forum: Engine Tech
- Topic: stopping rust in a 4 year old race motor
- Replies: 15
- Views: 1926
Re: stopping rust in a 4 year old race motor
I have used the product CLR with great results. CLR is Calcium, Lime, Rust. In Canada any hardware, department store will have it. I had a friend who bought a used Corvette. When a hydrometer was used to check the antifreeze, it was so brown/cloudy it couldn't be read!! I dumped it, then put water a...
- Mon May 10, 2021 9:21 am
- Forum: Engine Tech
- Topic: Question for those who build and sell engines
- Replies: 36
- Views: 3268
Re: Question for those who build and sell engines
Many years ago my Dad had a shop, we did Heavy Equipment Repairs, Heavy Truck Repairs, Auto Repairs and Small Engines. My Dad was a Certified Auto Technician and Certified Heavy Equipment Technician. I am a Certified Technician for Heavy Equipment, Truck & Coach, Automotive and Marine & Smal...
- Tue Apr 20, 2021 11:00 pm
- Forum: Engine Tech
- Topic: SBC Fuel Pressure
- Replies: 10
- Views: 1579
Re: SBC Fuel Pressure
Install a fuel pressure regulator.
- Mon Dec 21, 2020 10:03 pm
- Forum: Engine Tech
- Topic: Engine Combo Question
- Replies: 2
- Views: 393
Engine Combo Question
Hello, I have parts to build a 4.155" bore x 3.625" stroke, with a 6.000" rod, 2.00" rod pin and 12:5:1 pistons. However I am thinking of going with a 3.250 stroke crankshaft instead. Does anyone here know if the rods and pistons I have will work with the 3.250 stroke crank? Thanks
- Sat Oct 17, 2020 8:17 am
- Forum: Engine Tech
- Topic: Engine Oil
- Replies: 28
- Views: 2863
Engine Oil
Good day, Is anyone using Amsoil in their circle track engines? How do you like it? What grade are you using? What engine oil filter are most using? I have been using Penn Oil but it just doesn't seem the same anymore since the company changed hands. I use WIX racing filters and have been told that ...
- Sat Oct 03, 2020 7:06 am
- Forum: Engine Tech
- Topic: Dominator - can't even get it to idle
- Replies: 119
- Views: 12270
Re: Dominator - can't even get it to idle
I have read through most of the posts here and I have noticed that nobody has mentioned fuel pressure? I have had carb issues in the past and it all lead back to too much fuel pressure. Holley carbs like about 4 to 6.5 PSI. get a fuel pressure gauge and a regulator and check it out. Just another sug...
- Wed Mar 04, 2020 7:31 am
- Forum: Chassis / Suspension / Body
- Topic: Front Roll Centre
- Replies: 3
- Views: 1581
Front Roll Centre
Hello, Does anybody here know of, or have a good front roll centre height and distance left, for an IMCA style ICAR rule, asphalt modified, racing on a 1/4 mile semi banked race track? The front clip is an early 70's Impala, non-metric. I have changed to the #2 chev spindles. I changed the spindles ...
- Sun Feb 16, 2020 6:43 pm
- Forum: Engine Tech
- Topic: Camshaft Question
- Replies: 13
- Views: 1748
Re: Camshaft Question
Thank you sir, I will give you a call tomorrow.
Thanks again.
Thanks again.