Don Terrill’s Speed-Talk

I suppose your not allowed to use the W shaped or finned intake port floor. Would be a cool way to have fun with the port while complying with the cc rules. You can.. I tried it on my first engine. "I tried it on my first engine." did it gain HP ?? did it lose HP ??? or no difference in H...

289nate wrote: ↑Fri Apr 12, 2024 11:17 pm I suppose your not allowed to use the W shaped or finned intake port floor. Would be a cool way to have fun with the port while complying with the cc rules.

You can.. I tried it on my first engine.

So Larry I know you will appreciate this. This would be the Edelbrock that would replace the 041. This set is for a 350/300hp combo.

While I appreciate the purest, the aluminum head is bigger in volume to be legal.

jamie wrote: ↑Sat Apr 06, 2024 9:12 pm

SpeierRacingHeads wrote: ↑Sat Apr 06, 2024 2:48 pm Here is a 300-25 I done for a 350/360hp Super Stock engine. It hated it! Ended up pulling it and grinding it all back out while it was still on the dyno.

Chad,did you or were you allowed to use open spacers on this?

Yes we tried several.

Here is a 300-25 I done for a 350/360hp Super Stock engine. It hated it! Ended up pulling it and grinding it all back out while it was still on the dyno. Chad, was that with a Q-Jet Carb ??? its very hard to beat the Edelbrock Victor-E Manifold with a Q-Jet No this was a LT1 combo with a 780 vac se...

Here is a 300-25 I done for a 350/360hp Super Stock engine. It hated it! Ended up pulling it and grinding it all back out while it was still on the dyno.

Had to laugh. Working on a set of Indy AMC heads. The shape totally reminds me of a 23º Chevy.

It's NOT very thick for dang sure. Needs a smaller water jacket under the floor.

Yea.. no words needed.

He just won class as the Baby Gators today!

Customer just texted and I did a Super Stock manifold for him. This manifold. Said it's worth .06! NICE!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
MIGHT HAVE PICKED UP ANOTHER .04 SMOOTH! HA!

I can add that when I ordered my new CP pistons for the Super Stock engine, the first call was to the expert (no names) at Total Seal on what is the best rings to build the piston to. Long story short it's a $220 .7/.7/2mm set of rings.

fordified wrote: ↑Thu Feb 22, 2024 3:11 pm

COMP461 wrote: ↑Thu Feb 22, 2024 3:05 pm No it’s a 1984 Dodge Daytona 2.2 turbo. I ran a D/ED and C/ED in comp and SS/DM in SS.

I was responding to Speier about his car.

I got it as low as I could. Still has a 16" cam center. But I have to add weight so I will get it ironed out.

rapidride2 wrote: ↑Thu Feb 22, 2024 12:38 am Any programs available for the PB 1200 Brodix maneater 12 degree heads?

I do not...

Stock eliminator is not an entry level class and it’s not inexpensive. I’ve run every thing from Compitition eliminator to Super stock. I’ve stepping out of a Top dragster to stock and I feel it’s a tougher class and has more honor I would certainly argue that a good super stock engine is more labo...

A stocker valve job does not seal on the 45 seat! :wink: Not all heads have O.E.M. seat angle of 45 degrees ... though, that seat angle rule does not seem to be enforced these days; I think the newest rules, as written, may even have that part deleted. OK, so I will rephrase it. Whatever the OEM se...