Speed-Talk is running on www.Speed-Talk.com

IMPORTANT: Update your bookmarks to https://www.speed-talk.com/forum/
(Right-click the URL and select "Bookmark this link")

Search found 195 matches

by allencr267
Tue May 04, 2021 11:30 pm
Forum: Engine Tech
Topic: EFI Fuel Pressure Drop ~5psi
Replies: 20
Views: 619

Re: EFI Fuel Pressure Drop ~5psi

14ft of what?
Bends, restrictions, 90's, fittings?
In the below pic, is that the line, 3 or 4/16ths ID lean looking stainless.?
ctk30 wrote: Tue May 04, 2021 8:26 pm Image
by allencr267
Mon May 03, 2021 5:11 pm
Forum: Engine Tech
Topic: EFI Fuel Pressure Drop ~5psi
Replies: 20
Views: 619

Re: EFI Fuel Pressure Drop ~5psi

Where is the pressure read & regulated?
by allencr267
Sun May 02, 2021 5:24 pm
Forum: Engine Tech
Topic: honing question
Replies: 26
Views: 1486

Re: honing question

Belgian1979 wrote: Sun Apr 25, 2021 6:05 am Trust me ...have a ridge... ---very noticable...
Sorry, basics, Is it carbon or iron?
by allencr267
Sun Apr 18, 2021 8:50 am
Forum: Engine Tech
Topic: overheating question
Replies: 61
Views: 1545

Re: overheating question

It needs it at the radiator, its outlet.
by allencr267
Sun Apr 18, 2021 8:10 am
Forum: Engine Tech
Topic: overheating question
Replies: 61
Views: 1545

Re: overheating question

Fan temp sensor location not in the radiator's outlet?
by allencr267
Thu Oct 29, 2020 2:53 pm
Forum: Engine Tech
Topic: Motorcycle crankshaft specialty shops
Replies: 7
Views: 565

Re: Motorcycle crankshaft specialty shops

Engine Builder story from almost 2 years ago.

https://www.enginebuildermag.com/2018/1 ... omponents/
by allencr267
Sat Oct 24, 2020 5:50 pm
Forum: Engine Tech
Topic: SBC oil pan gasket help
Replies: 17
Views: 885

Re: SBC oil pan gasket help

Is it a 1 piece gasket, can you cut & paste a decent one, is the pan rail[block & sump] straight & smooth & clean?
by allencr267
Thu Oct 01, 2020 12:13 pm
Forum: Engine Tech
Topic: Cleaning out the garage...
Replies: 33
Views: 1986

Re: Cleaning out the garage...

There must be a Salvation Army, Habitat for Humanity or Lighthouse for the Blind or charity second hand/thrift shop that could use/sell any tools or supplies.
I hate good stuff getting trashed/scrapped.
by allencr267
Mon Aug 31, 2020 5:39 am
Forum: Engine Tech
Topic: Ford mech fuelpump for Webers
Replies: 17
Views: 1072

Re: Ford mech fuelpump for Webers

A smaller needle & seat can handle higher pressure.
IDK if one is available.
by allencr267
Sun Aug 02, 2020 5:13 pm
Forum: Engine Tech
Topic: Main Bearing Question
Replies: 17
Views: 699

Re: Main Bearing Question

Holding the crank up because you put in the pistons before it? Wouldn't it be hard to make that pattern from regular factory assembly line machining let alone local performance machine shop stuff? The cap looks cut, but not too pretty. Things were done intentional by old timers and some not so old i...
by allencr267
Tue Jul 28, 2020 9:13 am
Forum: Engine Tech
Topic: motor mounts
Replies: 22
Views: 743

Re: motor mounts

and torsion - twist
Sorry, really wrong word
by allencr267
Mon Jul 27, 2020 8:43 pm
Forum: Engine Tech
Topic: rocker arm oiling problem
Replies: 11
Views: 953

Re: rocker arm oiling problem

spec .032 orifice means nearly unlimited bevel/chamfer/radius.
by allencr267
Mon Jul 27, 2020 8:35 pm
Forum: Engine Tech
Topic: Rear gears
Replies: 14
Views: 754

Re: Rear gears

Is the best contact patch the best for power as well as quiet, different contact at the inside/bottom/root of the ring and any cryo snake oil testimony?
by allencr267
Mon Jul 27, 2020 8:25 pm
Forum: Engine Tech
Topic: motor mounts
Replies: 22
Views: 743

Re: motor mounts

...motor mounts can be taken out... [/u] Some might need the engine pushed a little sideways, besides up, to clear things, or cut new stud shorter. Mount/s installed with tension and compression? Slimy so called rubber oozing out? Visible active/fresh line between rubber and steel? Surface weather ...
by allencr267
Thu Jul 16, 2020 1:54 pm
Forum: Engine Tech
Topic: Cheap SBC aluminum heads..
Replies: 64
Views: 3212

Re: Cheap SBC aluminum heads..

Please give description, I/we don't need a pic, and especially a Youtube, if the observer has some ounces of experience, 20/30 or so with enhancement vision, can wiggle a stem in the guide & marker on a seat, observe the stem, keeper, retainer & spring fit and take a guess if they've used intakes fo...