Search found 68 matches
- Sun Oct 24, 2021 8:52 pm
- Forum: Engine Tech
- Topic: How far in do you drive the rear cam tunnel plug? And does it effect cam location?
- Replies: 5
- Views: 1117
Re: How far in do you drive the rear cam tunnel plug? And does it effect cam location?
Thanks for the help guys.
- Sun Oct 24, 2021 6:21 pm
- Forum: Engine Tech
- Topic: How far in do you drive the rear cam tunnel plug? And does it effect cam location?
- Replies: 5
- Views: 1117
Re: How far in do you drive the rear cam tunnel plug? And does it effect cam location?
Sorry, forgot to mention it's a gen 1 sbc 350.
- Sun Oct 24, 2021 3:51 pm
- Forum: Engine Tech
- Topic: How far in do you drive the rear cam tunnel plug? And does it effect cam location?
- Replies: 5
- Views: 1117
How far in do you drive the rear cam tunnel plug? And does it effect cam location?
Switching a ft block to roller cam, was wondering if the depth of the rear cam tunnel plug plays a part in cam location in the block. A Google search turns up some saying to just drive it in flush, others say 1/8th in past flush.
- Thu Oct 21, 2021 1:50 pm
- Forum: Engine Tech
- Topic: Timing belt drives and roller retrofit cams.
- Replies: 1
- Views: 481
Timing belt drives and roller retrofit cams.
When upgrading a ft sbc bock to a roller retrofit cam, are the belt drive setups fixed to properly locate the cam?
- Sun Oct 10, 2021 12:47 pm
- Forum: Engine Tech
- Topic: What distributor gear are you guys using for billet cams?
- Replies: 18
- Views: 3912
What distributor gear are you guys using for billet cams?
I ordered a Jones cam that I assume is billet, not sure which distributor gear to go with.
- Tue Sep 28, 2021 7:42 pm
- Forum: Engine Tech
- Topic: What cam would you use in this mix match of parts 355?
- Replies: 7
- Views: 975
Re: What cam would you use in this mix match of parts 355?
Cam# SBC, R74410-76410-110 244/251 @.050" .410"/.410" Lobe Lift .680"/.680" Net Valve Lift (after lash) w/1.7 rockers 110 LSA This is a little big for a 355, and will make peak HP at 6,800rpm When you upgrade to the 3.75" stroke, it will make peak HP at 6,400rpm Do you...
- Tue Sep 28, 2021 2:23 pm
- Forum: Engine Tech
- Topic: What cam would you use in this mix match of parts 355?
- Replies: 7
- Views: 975
Re: What cam would you use in this mix match of parts 355?
A 383 crank would go a long way to helping your project goals A solid street roller around 248/254 @.050 on 108lsa would Be a good starting point Eventually that's where I'm going but for now I'm stuck with what I have. Plan on buying a small base circle cam so I can continue using it when I upgrad...
- Mon Sep 27, 2021 10:01 pm
- Forum: Engine Tech
- Topic: What cam would you use in this mix match of parts 355?
- Replies: 7
- Views: 975
Re: What cam would you use in this mix match of parts 355?
A 383 crank would go a long way to helping your project goals A solid street roller around 248/254 @.050 on 108lsa would Be a good starting point Eventually that's where I'm going but for now I'm stuck with what I have. Plan on buying a small base circle cam so I can continue using it when I upgrad...
- Mon Sep 27, 2021 9:51 pm
- Forum: Engine Tech
- Topic: What cam would you use in this mix match of parts 355?
- Replies: 7
- Views: 975
What cam would you use in this mix match of parts 355?
It's a .030 over goodwrench block with no other machine work. 5.7 inch rods and flat top pistons. AFR 220s with 65cc chambers and 1.7 ratio crower shaft mount rockers. 5.7 inch rods. The springs are PAC 1.550" OD, 220 lbs on seat, .710" maximum lift, - 260* max recommended duration, Max RP...
- Sun Aug 09, 2020 6:33 pm
- Forum: Engine Tech
- Topic: Gen 3 Hemi cam phaser lock out.
- Replies: 4
- Views: 530
Gen 3 Hemi cam phaser lock out.
Any reason why I shouldn't just weld the phaser down instead of stuffing it with aluminum blocks like everyone else does?
- Thu Aug 06, 2020 1:58 pm
- Forum: Race Cars & Parts - For Sale or Wanted
- Topic: Junk/damaged AFR 220 eliminator head.
- Replies: 0
- Views: 613
Junk/damaged AFR 220 eliminator head.
need a junked head to cut up, anyone have one?
- Thu Aug 06, 2020 12:52 pm
- Forum: Engine Tech
- Topic: Speedmaster aluminum block
- Replies: 276
- Views: 36056
Re: Speedmaster aluminum block
I just read all 18 pages at work this morning. Thanks guys.
- Mon Aug 03, 2020 8:32 am
- Forum: Show & Tell
- Topic: A little outside the norm for this forum (racing karts)
- Replies: 2
- Views: 2641
Re: A little outside the norm for this forum (racing karts)
Nice rides man. I raced cr125s in the ahscs and some other series back in my younger days. Impressive numbers you're making.
- Sun Aug 02, 2020 5:05 am
- Forum: Vintage/Classic/Historical Engine Tech
- Topic: SBC based bike engine
- Replies: 8
- Views: 1384
- Sun Aug 02, 2020 4:51 am
- Forum: Engine Tech
- Topic: Motor for an Ultima
- Replies: 68
- Views: 4716