I am trying to reach Pipemax. I purchase the 3 package and I have on 1 pc. Need to install on another pc. Instruction was on old email that ATT canceled because it was spammed. How do I proceed from here. 76 years old and still lost
reed
Search found 957 matches
- Wed Apr 17, 2024 12:03 pm
- Forum: Engine Tech
- Topic: PIPEMAX question for maxracesoftware
- Replies: 6
- Views: 1183
- Wed Apr 10, 2024 1:09 pm
- Forum: Engine Tech
- Topic: Ron's head porting
- Replies: 6
- Views: 1028
Re: Ron's head porting
I have a good friend that purchased the head porting machines and programs when Ron closed. I can ask him if he can or would help me. PM me and we can talk
reed
reed
- Fri Mar 15, 2024 9:01 am
- Forum: Engine Tech
- Topic: Serv equip power stroke honing question
- Replies: 1
- Views: 176
Re: Serv equip power stroke honing question
I run the bore down to end of cylinder and then do a .010 undercut for as low as I can, at least .500 of rovertravel of hone. Post photos so we can see.
reed
reed
- Tue Mar 05, 2024 9:28 am
- Forum: Engine Tech
- Topic: Thinner piston pins and moving pin up in the piston
- Replies: 12
- Views: 655
Re: Thinner piston pins and moving pin up in the piston
If u go to a certain point on pins, u better put extra clearance in piston or the pin will pinch. Ask me how I know
reed
reed
- Tue Mar 05, 2024 9:26 am
- Forum: Engine Tech
- Topic: Dart Pro 1 heads-Backcut
- Replies: 7
- Views: 536
Re: Dart Pro 1 heads-Backcut
On my flow bench, Ive always found gain with a back cut, BUT not always on my dyno. For my engine, I back cut intake valve but never back cut exhaust.. Reversion can rear its ugly head more than u think but cam and headers play a huge part in that. So choose your medicine.
reed
reed
- Tue Feb 20, 2024 2:14 pm
- Forum: Engine Tech
- Topic: SBC rod to cam clearance
- Replies: 14
- Views: 984
Re: SBC rod to cam clearance
Just make sure u get stroker rods. Some move the bolt to get more clearance
]reed
]reed
- Tue Feb 20, 2024 2:12 pm
- Forum: Engine Tech
- Topic: Balance question
- Replies: 6
- Views: 556
Re: Balance question
Longer rod will present no problem on counterweights. Only problem is counterweights may be cut to much to your balancing liking. Only way to know is pre-way everything and see how it looks to their target weight. If I get a job out that require more than one or two holes, I call customer and tell h...
- Tue Feb 20, 2024 2:08 pm
- Forum: Engine Tech
- Topic: Comp Evolution lifters
- Replies: 10
- Views: 702
Re: Comp Evolution lifters
I stopped using hyd roller liters over a year ago. I only use solid roller on hyd grind. Have yet to have a problem. I had so many damn problems and failures with hyd
reed
reed
- Sat Feb 17, 2024 10:05 am
- Forum: Engine Tech
- Topic: Bent roller camshafts
- Replies: 4
- Views: 485
Re: Bent roller camshafts
Is the cam cast or steel. I will straighten a cast cam only if under .005. Ive straightened steel up to .030 but do it slowly and then set it with a blunt punch. Ive also straightened with cold water and heat but u better know the steel to do that.
reed
reed
- Mon Feb 05, 2024 3:45 pm
- Forum: Engine Tech
- Topic: .842 solid roller lifter needle or bushed??
- Replies: 22
- Views: 1616
Re: .842 solid roller lifter needle or bushed??
Ive had 4 engines come back in this year (2023) that lost roller lifters. 2 were .842, one was .875 and had one Mopar at .903(my first of this). As might think, had a lot of damage. Have gone to bushed to try to help. Have flooded the lifter with oil and took pressure up 5 psi to ensure oiling. Wait...
- Tue Jan 02, 2024 12:42 pm
- Forum: Engine Tech
- Topic: Custom pistons or zero deck the block with off-the-shelf pistons?
- Replies: 16
- Views: 12758
Re: Custom pistons or zero deck the block with off-the-shelf pistons?
JE owns Wiseco or vice versa, either way one and the same
- Tue Jan 02, 2024 10:33 am
- Forum: Engine Tech
- Topic: Custom pistons or zero deck the block with off-the-shelf pistons?
- Replies: 16
- Views: 12758
Re: Custom pistons or zero deck the block with off-the-shelf pistons?
You will find thaat unless you offset grind the crank yourself, that it will cost more to do that than the extra price on piston. I offset grind some cranks, but it is not cheap and you better know who u get to do it. Most will miss the index. Decking .020 off the deck will not hurt it but trim some...
- Tue Sep 05, 2023 9:13 am
- Forum: Engine Tech
- Topic: Overbalanced 3.75” SBC crank and vibration
- Replies: 28
- Views: 2370
Re: Overbalanced 3.75” SBC crank and vibration
Been balancing engines for many years and selling balance machines for 15+{ years. Never gone more than 1% on over or underbalance. In fact very seldom do either of these for a street machine. Explain the theory for 4% please
reed
reed
- Tue Aug 15, 2023 11:32 am
- Forum: Engine Tech
- Topic: Chevy 327 Deck Clearance?
- Replies: 21
- Views: 1423
Re: Chevy 327 Deck Clearance?
Sounds like it may have a cheap rebuild set of pistons that comes deeper in the hole to make up for a block that had to be decked. Doesnt matter, giving up waay to much on compression.
reed
reed
- Fri Jun 09, 2023 3:40 pm
- Forum: Engine Tech
- Topic: Speedmaster aluminum block
- Replies: 276
- Views: 36066
Re: Speedmaster aluminum block
Well, I wish I read all of these comments before I purchased a Speedmaster aluminum SBC. I purchased what was supposed to be a “fully machined block”, yet I had to have it “decked” as the liners stuck out of the deck. Also, had to have it finished honed to fit my pistons. Those and cam bearings ins...