Search found 184 matches
- Thu Jan 25, 2024 6:20 am
- Forum: Chassis / Suspension / Body
- Topic: power steering fluid cooler
- Replies: 2
- Views: 474
power steering fluid cooler
was watching Roadkill on tv and they installed a transmission style cooler for the steering, what kind of application requires this? do big trucks use steering coolers?
- Thu Jan 25, 2024 6:15 am
- Forum: Engine Tech
- Topic: Rebuilding a 350 HEADS
- Replies: 15
- Views: 900
Re: Rebuilding a 350 HEADS
factory small block Chevy heads were known to be thin around the spring seats, which led to people using unusual tactics to overcome this problem in performance applications, tools were developed to reshape the spring seats and top of the valve guide in one machine operation, what is the diameter of...
- Fri Dec 29, 2023 8:27 am
- Forum: Engine Tech
- Topic: 400 dart shp build
- Replies: 40
- Views: 31063
Re: 400 dart shp build
Weingartner has videos where the runners lengths and openings areas are measured of various SBC manifolds, his dyno tests are not very helpful when it comes to street use but theoretically longer runners and smaller cross sections should help street rpm range
- Thu Dec 28, 2023 5:33 am
- Forum: Engine Tech
- Topic: 400 dart shp build
- Replies: 40
- Views: 31063
Re: 400 dart shp build
what is the height available for the intake? distance from the china wall to the hood? do the headlights operate off vacuum?
- Tue Dec 19, 2023 7:19 am
- Forum: Engine Tech
- Topic: Intake Manifold testing
- Replies: 169
- Views: 28264
Re: Intake Manifold testing
agree, the term "port matched" has been misused constantly when the correct term is "gasket matched" for manifolds, very few SBC and BBC aftermarket heads have port openings that are identical to the common gaskets, the corner radius just isn't the same as 1960's Chevy heads, so ...
- Sun Dec 10, 2023 7:45 am
- Forum: Engine Tech
- Topic: How good were caddy 500's really?
- Replies: 34
- Views: 10769
Re: How good were caddy 500's really?
what makes the engine 75 pounds lighter than BBC? what is the deck height? I could see the canted valve heads add 25# what else?
- Mon Nov 27, 2023 7:40 am
- Forum: Engine Tech
- Topic: ZZ3/4 intake vs. Perf RPM Q-jet
- Replies: 25
- Views: 2729
Re: ZZ3/4 intake vs. Perf RPM Q-jet
does the first table for the low manifolds say 471 hp for the ZZ4 and the later table for all manifolds say 451 hp? maybe I can't follow the article
- Fri Oct 27, 2023 7:46 am
- Forum: Engine Tech
- Topic: Chevy 327 Tunnel Ram Idling To Fast When Started
- Replies: 21
- Views: 1967
Re: Chevy 327 Tunnel Ram Idling To Fast When Started
linkage needs to be gone over carefully, maybe disconnect the linkage from each carb leaving a functional return spring for each, I don't know anything about the choke and fast idle setup for that type carb but tinker with them one carb at a time, obviously check the base gaskets for vacuum keaks
- Thu Jul 27, 2023 9:18 am
- Forum: Engine Tech
- Topic: Overbalanced 3.75” SBC crank and vibration
- Replies: 28
- Views: 2360
Re: Overbalanced 3.75” SBC crank and vibration
is there a cheap from Amazon style tool that will measure vibration?
- Sun Jun 18, 2023 6:06 am
- Forum: Vintage/Classic/Historical Engine Tech
- Topic: Filling blocks
- Replies: 22
- Views: 3644
Re: Filling blocks
Masterflow 885 grout is commonly used in drag racing with stock type iron engine blocks
- Sun Jun 18, 2023 5:58 am
- Forum: Engine Tech
- Topic: Engine Masters (MotorTrend) Tests Oil Viscosity
- Replies: 70
- Views: 7375
Re: Engine Masters (MotorTrend) Tests Oil Viscosity
on the Motortrend cable channel the other night they were driving a used up SBC that was going about 10 miles per quart of oil, what current oil and or additive will help with terrible ring seal for let's say a month?
- Fri Jun 09, 2023 10:35 am
- Forum: Engine Tech
- Topic: Low RPM Mark VI 454 Intake and Cam Choices?
- Replies: 14
- Views: 1195
Re: Low RPM Mark VI 454 Intake and Cam Choices?
how do the exhaust manifolds from a C60 type 427 truck compare to pickup manifolds? manifolds are going to hurt power in the mid range compared to long tube headers
- Sun Jun 04, 2023 9:30 am
- Forum: Engine Tech
- Topic: dished piston quench height?
- Replies: 9
- Views: 804
Re: dished piston quench height?
most replacement pistons have reduced compression height to account for decked heads and block, if those are stock bore you might use a straight edge ruler and feeler gauge to find out what you have
- Tue May 30, 2023 6:16 pm
- Forum: Engine Tech
- Topic: AFR guideplates
- Replies: 4
- Views: 464
Re: AFR guideplates
I wanted to order studs, plates, and rockers over the holiday, these no name chinese heads take about .670" thread depth before intruding into the port enough to make me consider cutting some off
- Sun May 28, 2023 5:41 pm
- Forum: Engine Tech
- Topic: AFR guideplates
- Replies: 4
- Views: 464
AFR guideplates
does anyone know the thickness of their SBC adjustable plate? .090" ? more ?