Search found 3098 matches
- Thu Aug 05, 2010 8:11 am
- Forum: Engine Tech
- Topic: Honda Journal Rods
- Replies: 12
- Views: 2516
Re: Honda Journal Rods
Ok..thanks..is there any advantage to either one..Honda or IRL ? In your application probably very little. There are small advantages such as the use of a smaller housing bore (along with the slight reduction in weight and bearing speed). The advantages of the smaller housing bore, in the case of t...
- Wed Aug 04, 2010 9:25 am
- Forum: Engine Tech
- Topic: Rod bearing clearance question
- Replies: 111
- Views: 16856
Re: Rod bearing clearance question
As for your videos with your motors lasting for 150,000 miles with .0015 clearances, well so what? You could run the same red traffic light 100 times with no accidents but that does not mean it is safe to run that red traffic light. Maybe you just got lucky. so for over 20 years i must have been ri...
- Mon Aug 02, 2010 10:13 am
- Forum: Engine Tech
- Topic: Spark Plug Thread Lubrication?
- Replies: 57
- Views: 23251
Re: Spark Plug Thread Lubrication?
Warpspeed, I have a question for you. On some of the SB2 stuff I've done the electrode breaks off of the plug at the base. I've talked to others that have seen the same thing. And no it's not detonation burning the electrode off, they just break off. I see the Cup guys are using X plugs, did they g...
- Mon Aug 02, 2010 10:07 am
- Forum: Engine Tech
- Topic: Rod bearing clearance question
- Replies: 111
- Views: 16856
Re: Rod bearing clearance question
Warp Speed, I asked you a question in another post a week or so ago. On a few of the SB2s I've done, they break the spark plug ground strap off right at the weld. I talked to another builder about this and he had observed the same thing. Is this one of the reasons they went to the X plug? Robert, T...
- Sun Aug 01, 2010 6:48 pm
- Forum: Engine Tech
- Topic: Rod bearing clearance question
- Replies: 111
- Views: 16856
Re: Rod bearing clearance question
By the way I use the little stringy things from "bananas" as plastigage!! Was that supposed to be a dig??? LOL :lol: Need to try a little harder next time! I used wide clearances as you do (along with 40w Kendal) and won many races and championships with it. That was 20 years ago though, ...
- Sun Aug 01, 2010 12:12 pm
- Forum: Engine Tech
- Topic: Rod bearing clearance question
- Replies: 111
- Views: 16856
Re: Rod bearing clearance question
OK.....so I spoke too soon! LOL ^^^^^^^^^^^
- Sun Aug 01, 2010 7:47 am
- Forum: Engine Tech
- Topic: Rod bearing clearance question
- Replies: 111
- Views: 16856
Re: Rod bearing clearance question
Pretty good thread considering this topic usually gets out of hand pretty quick! LOL There has been some good info/data posted (Rob/RW TECH). One thing that is always brought up when talking bearing clearances is the Darren Morgan post. The article referenced is a bit old, and I would bet his opinio...
- Fri Jul 16, 2010 7:44 am
- Forum: Engine Tech
- Topic: Lifter Bore Honing Tool
- Replies: 41
- Views: 9992
Re: Lifter Bore Honing Tool
And I was right!!! LOLWarp Speed wrote:This thread could turn into a mess!! LOL
Carl at the office!!! LOL
- Wed Jul 14, 2010 12:40 pm
- Forum: Engine Tech
- Topic: Lifter Bore Honing Tool
- Replies: 41
- Views: 9992
Re: Lifter Bore Honing Tool
This thread could turn into a mess!! LOL
- Fri Jun 18, 2010 8:21 am
- Forum: Engine Tech
- Topic: Spark Plug Thread Lubrication?
- Replies: 57
- Views: 23251
Re: Spark Plug Thread Lubrication?
We use Coposlip high temp anti-sieze on the threads of all of our spark plugs. We have done extensive testing with Bosch on this, and this is about the only lube that provides the best grounding and temp transfer, while still providing the needed lubrication to get them out without damage. You do ne...
- Sat May 29, 2010 3:06 pm
- Forum: Engine Tech
- Topic: Honing lifter bores
- Replies: 94
- Views: 16613
Never Mind!!!
Your The Man!
- Sat May 29, 2010 10:52 am
- Forum: Engine Tech
- Topic: Honing lifter bores
- Replies: 94
- Views: 16613
Re: Honing lifter bores
Number one their are more guys honing lifter bores on this site then the boat And just what does that have to do with anything, and that is not the reason you puled this over here. As stated bellow, you are just looking for your cheering section. If you read this quote it pretty much reads honing i...
- Thu May 27, 2010 2:28 pm
- Forum: Engine Tech
- Topic: Honing lifter bores
- Replies: 94
- Views: 16613
Re: Honing lifter bores
CNC BLOCKS wrote:
Your machining plastic parts and I machining engine parts some how I feel there is diffearance between the 2 HMMMMMMMMMMMMMMMMM
Carl
Yes there is, mine are on size.......!!! LOL
Sorry.........you walked right into it!!!
- Thu May 27, 2010 1:46 pm
- Forum: Engine Tech
- Topic: Honing lifter bores
- Replies: 94
- Views: 16613
Re: Honing lifter bores
Can you read, or just what you want to read?
Warp Speed wrote:As I said before, .001 term was an exagerated example used for effect
- Thu May 27, 2010 12:28 pm
- Forum: Engine Tech
- Topic: Honing lifter bores
- Replies: 94
- Views: 16613
Re: Honing lifter bores
It's classic that you always bring up "what do you own" to everyone who questions you, or has a differant opinion. What does "MY" equipment have to do with my knowledge, or my machining and measuring principles? If you have good credit it automaticly makes you a knowledgable mach...