Lowbuck Shop/Race Truck Build
Moderator: Team
Lowbuck Shop/Race Truck Build
A few years back I decided to build a 1979 big ten Chevy truck, my goal was to teach my son how to build a fun driver with out spending a bunch of money, and more important out of parts most people would discard. So I bought this very rusty C-10 long bed for 900.00, we stripped the drive train out of it and cleaned it up. We had a few virgin 327s left over bought for a 302 build, so we built a 327, pretty much did everything backwards from how it should be done, but its been fun. So we built a 11.1 327 with speedpro pistons, we used a Isky 480/240/108 solid lifter cam with 462 fuelie heads with Performer RPM intake and 750 double pumper carb. I used reproduction Z/28 pulleys. The original long shaft Turbo 350 was rebuilt with a shift kit hooked to a 2 piece drive shaft (more on that later). Luckily my 79 being a Big 10 had a truck 12 bolt but has a 3.07 open carrier. So I'am at the point where I want to turn it up, and here are my plans.
1. Build a new truck 12 bolt with 5.13 gears, with a car bolt pattern
2. Replace the ridiculously heavy 2 piece drive shaft a aluminum one piece
3. Use lightweight rims front and back
I will post some pictures as the truck sits today before the modifications, along with my rear end build.
1. Build a new truck 12 bolt with 5.13 gears, with a car bolt pattern
2. Replace the ridiculously heavy 2 piece drive shaft a aluminum one piece
3. Use lightweight rims front and back
I will post some pictures as the truck sits today before the modifications, along with my rear end build.
You do not have the required permissions to view the files attached to this post.
Racing a NA NHRA stocker should be mandatory before any posting.
- af2
- Guru
- Posts: 7014
- Joined: Sun Jan 28, 2007 4:42 pm
- Location: Grass Valley, CA :Northern Foothills
Re: Lowbuck Shop/Race Truck Build
This is not the same Vortecpro we are used to.
GURU is only a name.
Adam
Adam
Re: Lowbuck Shop/Race Truck Build
You already have the GM “big car” 5 bolt pattern...same as impala’s, caprice’s, etc. It is a very common pattern.
The problem with a 1 piece driveshaft in these is the length. My 3/4 ton suburban has a factory 1 piece aluminum driveshaft and it isn’t exactly light, as it is 5”-6” in diameter. High driveshaft speeds with the length will whip and bow so you have to use a bigger diameter...and you will have plenty of driveshaft speed with 5.13’s.
Also, the 12 bolt truck rear end isn’t quite as strong as a 12 bolt car unit, so be mindful of that.
The problem with a 1 piece driveshaft in these is the length. My 3/4 ton suburban has a factory 1 piece aluminum driveshaft and it isn’t exactly light, as it is 5”-6” in diameter. High driveshaft speeds with the length will whip and bow so you have to use a bigger diameter...and you will have plenty of driveshaft speed with 5.13’s.
Also, the 12 bolt truck rear end isn’t quite as strong as a 12 bolt car unit, so be mindful of that.
-
- Pro
- Posts: 397
- Joined: Tue Dec 29, 2015 8:09 pm
- Location: TN
Re: Lowbuck Shop/Race Truck Build
A few of the driveline sites offer calculators that can help you in the direction of a driveshaft. Depending on your tire size, a 1:1 ratio T350 and 5:13’s might be concerning depending on how high you plan to buzz it. Critical driveshaft speed is a function of the shaft’s length, material stiffness and tubing diameter.
Re: Lowbuck Shop/Race Truck Build
Fantastic father and son project ! I saw the engine begin dynoed on youtube and it’s very stout ! What converter are you using behind it in the truck ? And what does a truck like this weight ?
Re: Lowbuck Shop/Race Truck Build
FWIW, a 12-bolt tuck rearends pinion shAAFT IS A LOT SMALLER THAN A CAR 'S 12-BOLT ONE.
mY OLD '80 c/k 10 HAD ONE UNDER IT AS WELL AS 2.76 GEARS. iT ALSO HAD A 3.50 1ST GEAR sAG TRANNY IN IT.
PDQ67
dAMMED CAPS
mY OLD '80 c/k 10 HAD ONE UNDER IT AS WELL AS 2.76 GEARS. iT ALSO HAD A 3.50 1ST GEAR sAG TRANNY IN IT.
PDQ67
dAMMED CAPS
Re: Lowbuck Shop/Race Truck Build
If it were me, I’d rethink step #2. I went down this road with my 66’ C10. Was using it for mainly drag racing (434 sbc, th350, 12-bolt ) and thought I’d make an improvement by replacing that lowly 2-piece shaft with a custom built 1-piece unit. Turned out to be a mistake on my part. I had a nagging vibration at high vehicle speeds that was caused by the 1-piece bowing and whipping. I had a heavy-duty 2-piece shaft built, yanked that 1-piece back out, and replaced it with the h.d. 2-piece. No more vibration problems. Btw, my 66’ is a long bed.
Just my experiences.
Just my experiences.
Re: Lowbuck Shop/Race Truck Build
Also, fwiw, I think your 12-bolt will be fine. My truck weighs 4000 with me in it and has been 1.45 60 fts. with the truck 12-bolt.
Re: Lowbuck Shop/Race Truck Build
ATI converter. Weight is 4000 pounds.
Racing a NA NHRA stocker should be mandatory before any posting.
Re: Lowbuck Shop/Race Truck Build
The 1985 Nhra Stock C-10 low compression 350 combination have run 11.90s with 1.47 60s @ 3800 and change. I will try a OEM 5 inch shaft, if that doesn't work I will put the super heavy factory 2 piece back in there that goes every direction but strait.
You do not have the required permissions to view the files attached to this post.
Racing a NA NHRA stocker should be mandatory before any posting.
Re: Lowbuck Shop/Race Truck Build
Yes goes every direction but straight!
Mark what rear suspension you going with?
www.autotransdesign.com www.gzmotorsports.com
www.cranecams.com www.prosystemsracing.com
www.hardblok.com
Please say a prayer for all that serve and gave all to serve this Holiday and everyday!
www.cranecams.com www.prosystemsracing.com
www.hardblok.com
Please say a prayer for all that serve and gave all to serve this Holiday and everyday!
Re: Lowbuck Shop/Race Truck Build
Look at that young racer getting after it. Mark will have another winner in his stable soon. Keep us posted, always enjoy your builds.
Re: Lowbuck Shop/Race Truck Build
8” i assume ? It will be great to hear how it will do on the strip !
Re: Lowbuck Shop/Race Truck Build
Stock until I have to make a change.trmnatr wrote: ↑Sun Jul 26, 2020 10:53 pmYes goes every direction but straight!
Mark what rear suspension you going with?
Racing a NA NHRA stocker should be mandatory before any posting.