13100 rpm fourbanger restricted to 9300 redline
Moderator: Team
Re: 13100 rpm fourbanger restricted to 9300 redline
Does anyone have the maps for the secondary throttle opening as a function rpm for a 10-15 year old GSX-R600? Even ballpark measurement from the resistance would be useful. I’m curious how much the factory wanted to bias the air flow and reduce the intake runner CSA at 7000-9300 rpm range.
Paradigms often shift without the clutch -- https://www.youtube.com/watch?v=cxn-LxwsrnU
https://www.instagram.com/ptuomov/
Put Search Keywords Here
https://www.instagram.com/ptuomov/
Put Search Keywords Here
Re: 13100 rpm fourbanger restricted to 9300 redline
Can anyone tell the GSX-R600 engine model year from these codes? They’d have to remove the engine from the chassis to see the actual N7... engine numbers.
You do not have the required permissions to view the files attached to this post.
Paradigms often shift without the clutch -- https://www.youtube.com/watch?v=cxn-LxwsrnU
https://www.instagram.com/ptuomov/
Put Search Keywords Here
https://www.instagram.com/ptuomov/
Put Search Keywords Here
Re: 13100 rpm fourbanger restricted to 9300 redline
That sounds about right. Modifying the intake should be worth at least that much more again.
High Speed Combustion Pressure Tuning Equipment
TFX Engine Technology Inc.
tfx.engine@yahoo.com
www.tfxengine.com
TFX Engine Technology Inc.
tfx.engine@yahoo.com
www.tfxengine.com
Re: 13100 rpm fourbanger restricted to 9300 redline
This was with longer trumpets inside the stock air box, in addition to modified exhaust.
The intake runner diameter is difficult to modify within the rules. The throttle body elements are short and full of throttles. The short section that couples the throttle bodies to the cylinder head is also very short and furthermore molded from rubber. The head can’t be modified and intake manifold and throttle body parts need to be (potentially modified) original parts. Looking at the parts from photos and diagrams, reducing the intake tract diameter to produce stronger pulse would likely loose a ton with poor shapes.
The longer trumpets inside the air box and managing the cross-cylinder Helmholtz resonance effects with air box volume are more feasible paths.
The exhaust is modified stock exhaust. With extra time and money, a full custom exhaust could be made from scratch. The chassis is different from a motorcycle chassis so there’s some obvious improvements one could make, beyond just lengths and diameters.
Paradigms often shift without the clutch -- https://www.youtube.com/watch?v=cxn-LxwsrnU
https://www.instagram.com/ptuomov/
Put Search Keywords Here
https://www.instagram.com/ptuomov/
Put Search Keywords Here
-
- Guru
- Posts: 1547
- Joined: Thu Sep 29, 2011 8:55 am
- Location:
Re: 13100 rpm fourbanger restricted to 9300 redline
Sleeve the throttles down? In a concentric fashion?
Re: 13100 rpm fourbanger restricted to 9300 redline
It's a possibility, but I hate the idea of bringing the CSA down upstream given that the intake tract has that S-shape in it. It's a motor-cycle packaging issue. I'd be much less concerned if the intake runner and throttles would simply extend the port straight instead of curving "up".
Compared to many other ports, though, it’s damn straight. Still, I’d want to add more on the short side.
Paradigms often shift without the clutch -- https://www.youtube.com/watch?v=cxn-LxwsrnU
https://www.instagram.com/ptuomov/
Put Search Keywords Here
https://www.instagram.com/ptuomov/
Put Search Keywords Here
-
- Guru
- Posts: 1547
- Joined: Thu Sep 29, 2011 8:55 am
- Location:
Re: 13100 rpm fourbanger restricted to 9300 redline
https://youtu.be/RrIbNCwiqkI
Maybe you need to do some in metal for just the port floor.
And even under the secondary throttle, cut the bottom off that butterfly
Maybe you need to do some in metal for just the port floor.
And even under the secondary throttle, cut the bottom off that butterfly
Re: 13100 rpm fourbanger restricted to 9300 redline
That's illegal what they did in the video to the head, but it may be possible to do something like that to the throttle body and have the insert protrude out into the intake port from the throttle body.englertracing wrote: ↑Mon Mar 22, 2021 3:29 pm https://youtu.be/RrIbNCwiqkI
Maybe you need to do some in metal for just the port floor.
And even under the secondary throttle, cut the bottom off that butterfly
Paradigms often shift without the clutch -- https://www.youtube.com/watch?v=cxn-LxwsrnU
https://www.instagram.com/ptuomov/
Put Search Keywords Here
https://www.instagram.com/ptuomov/
Put Search Keywords Here
Re: 13100 rpm fourbanger restricted to 9300 redline
Changing the surface finish effectively changes the CSA.
Re: 13100 rpm fourbanger restricted to 9300 redline
In some ways it does, in other ways it does not.
Paradigms often shift without the clutch -- https://www.youtube.com/watch?v=cxn-LxwsrnU
https://www.instagram.com/ptuomov/
Put Search Keywords Here
https://www.instagram.com/ptuomov/
Put Search Keywords Here
Re: 13100 rpm fourbanger restricted to 9300 redline
Just a quick one from what i have seen on different generations of 1 engine
as the years went on the bhp was higher but so too was the rpm , the newer had way smaller intake valves and ports , it goes completely against general thoughts ,
head gaskets / skim heads play around as it advances/ retards the timing, and no one can say a thing , used here in rallying alot
some of the factory manuals give timing for optimum , as in deg timing on the std pullies , this could have being what you were following
as the years went on the bhp was higher but so too was the rpm , the newer had way smaller intake valves and ports , it goes completely against general thoughts ,
head gaskets / skim heads play around as it advances/ retards the timing, and no one can say a thing , used here in rallying alot
some of the factory manuals give timing for optimum , as in deg timing on the std pullies , this could have being what you were following
Re: 13100 rpm fourbanger restricted to 9300 redline
gunt wrote: ↑Wed Mar 24, 2021 7:29 am Just a quick one from what i have seen on different generations of 1 engine
as the years went on the bhp was higher but so too was the rpm , the newer had way smaller intake valves and ports , it goes completely against general thoughts ,
head gaskets / skim heads play around as it advances/ retards the timing, and no one can say a thing , used here in rallying alot
some of the factory manuals give timing for optimum , as in deg timing on the std pullies , this could have being what you were following
I can affirm that. The BMW S1000RR in 2015 went with smaller exhaust ports compared to the earlier cylinder head. Torque was improved without losing anything, which backs up what Calvin has been saying all along.
Been meaning to muck about with a very expensive epoxy to play with exhaust ports. From my research it would be good for NA only temperatures.
-
- Guru
- Posts: 9633
- Joined: Tue Nov 27, 2007 9:27 am
- Location: Chicago
- Contact:
Re: 13100 rpm fourbanger restricted to 9300 redline
Yes, but only at certain locations and higher speeds; not measurable on a low pressure flow bench.
Changes in discharge coefficient are often overlooked in the mad pursuit of increased volume flow.
Volume flow does not matter; only mass flow matters.
Blair has demonstrated a wide range of Cd values for various pressure ratios and valve lifts; which are
often overlooked or ignored.
-
- Guru
- Posts: 1547
- Joined: Thu Sep 29, 2011 8:55 am
- Location:
Re: 13100 rpm fourbanger restricted to 9300 redline
Can you pick and choose what year parts?
For example
Allegedly Smallest ports and valves from newest
Smallest cams from oldest.
For example
Allegedly Smallest ports and valves from newest
Smallest cams from oldest.
Re: 13100 rpm fourbanger restricted to 9300 redline
Can’t, since the service manual doesn’t instruct interchangeability.englertracing wrote: ↑Wed Mar 24, 2021 12:40 pm Can you pick and choose what year parts?
For example
Allegedly Smallest ports and valves from newest
Smallest cams from oldest.
However if you can get the head to rust and corrode, you can skim it no problem. And cam sprocket bolt holes that weren’t torqued properly can easily wear to oval shape. Etc.
Paradigms often shift without the clutch -- https://www.youtube.com/watch?v=cxn-LxwsrnU
https://www.instagram.com/ptuomov/
Put Search Keywords Here
https://www.instagram.com/ptuomov/
Put Search Keywords Here