Erson cams curiosity
Moderator: Team
-
- Expert
- Posts: 709
- Joined: Mon Aug 25, 2008 9:38 pm
- Location:
Erson cams curiosity
For those racing with Erson Cams, who is the go-to person for drag race, SBC, Methanol fuel?
Larry Woodfin - Team Woodfin Racing - Owner, Woodfin Automotive
Re: Erson cams curiosity
I believe one of the Erson Cams tech/sales reps is a member of this forum..
Re: Erson cams curiosity
viewtopic.php?f=20&t=55184
Russ Yoder’s contact info is in the above post.
I’m not sure if they have a cam core availability issue or what, but a whole lot of their off the shelf grinds haven’t been available for quite some time
Russ Yoder’s contact info is in the above post.
I’m not sure if they have a cam core availability issue or what, but a whole lot of their off the shelf grinds haven’t been available for quite some time
- Stan Weiss
- Vendor
- Posts: 4815
- Joined: Tue Feb 20, 2007 1:31 pm
- Location: Philadelphia, PA
- Contact:
Re: Erson cams curiosity
That maybe the answer to someone else's question but does not answer the question Larry asked.
Stan
Stan Weiss/World Wide Enterprises
Offering Performance Software Since 1987
http://www.magneticlynx.com/carfor/carfor.htm
David Vizard & Stan Weiss' IOP / Flow / Induction Optimization Software
http://www.magneticlynx.com/DV
Offering Performance Software Since 1987
http://www.magneticlynx.com/carfor/carfor.htm
David Vizard & Stan Weiss' IOP / Flow / Induction Optimization Software
http://www.magneticlynx.com/DV
Re: Erson cams curiosity
This member who represents the company, is probabily the best person to lead the OP to the guy he is looking for.Stan Weiss wrote: ↑Mon Jul 05, 2021 1:11 pmThat maybe the answer to someone else's question but does not answer the question Larry asked.
Stan
- Stan Weiss
- Vendor
- Posts: 4815
- Joined: Tue Feb 20, 2007 1:31 pm
- Location: Philadelphia, PA
- Contact:
Re: Erson cams curiosity
Let's wait and see what Larry says. But I believe that is that what he is looking for. I believe Larry wanted some member here who has used Erson Cams and had good result to tell Larry who he talked with.F-BIRD'88 wrote: ↑Mon Jul 05, 2021 2:16 pmThis member who represents the company, is probabily the best person to lead the OP to the guy he is looking for.Stan Weiss wrote: ↑Mon Jul 05, 2021 1:11 pmThat maybe the answer to someone else's question but does not answer the question Larry asked.
Stan
Stan
Stan Weiss/World Wide Enterprises
Offering Performance Software Since 1987
http://www.magneticlynx.com/carfor/carfor.htm
David Vizard & Stan Weiss' IOP / Flow / Induction Optimization Software
http://www.magneticlynx.com/DV
Offering Performance Software Since 1987
http://www.magneticlynx.com/carfor/carfor.htm
David Vizard & Stan Weiss' IOP / Flow / Induction Optimization Software
http://www.magneticlynx.com/DV
Re: Erson cams curiosity
Are you all done, now?Stan Weiss wrote: ↑Mon Jul 05, 2021 2:44 pmLet's wait and see what Larry says. But I believe that is that what he is looking for. I believe Larry wanted some member here who has used Erson Cams and had good result to tell Larry who he talked with.F-BIRD'88 wrote: ↑Mon Jul 05, 2021 2:16 pmThis member who represents the company, is probabily the best person to lead the OP to the guy he is looking for.Stan Weiss wrote: ↑Mon Jul 05, 2021 1:11 pm
That maybe the answer to someone else's question but does not answer the question Larry asked.
Stan
Stan
Re: Erson cams curiosity
If that is the case then my machinist has told me about an engine he recently built for a customer and which the customer had ordered from Erson cams a solid f/t and went on to tell me about how surprised they were with the power it made on the dyno.Stan Weiss wrote: ↑Mon Jul 05, 2021 2:44 pmLet's wait and see what Larry says. But I believe that is that what he is looking for. I believe Larry wanted some member here who has used Erson Cams and had good result to tell Larry who he talked with.F-BIRD'88 wrote: ↑Mon Jul 05, 2021 2:16 pmThis member who represents the company, is probabily the best person to lead the OP to the guy he is looking for.Stan Weiss wrote: ↑Mon Jul 05, 2021 1:11 pm
That maybe the answer to someone else's question but does not answer the question Larry asked.
Stan
Stan
-
- Expert
- Posts: 709
- Joined: Mon Aug 25, 2008 9:38 pm
- Location:
Re: Erson cams curiosity
The post just above this one answered my question. Thanks to all.
Larry Woodfin - Team Woodfin Racing - Owner, Woodfin Automotive
Re: Erson cams curiosity
WTH??? I took a bath this monthDragsinger wrote: ↑Mon Jul 05, 2021 10:46 pm The post just above this one answered my question. Thanks to all.
Re: Erson cams curiosity
I used them with a late model SBC roller with the 4/7 swap and Johnson roller lifters- except for the usual sticker shock shipping to canada- all is well.
Re: Erson cams curiosity
John x8002 at erson is the person to talk to.
Hes very busy and very helpful. Talk to him regularly.
Hes very busy and very helpful. Talk to him regularly.
Re: Erson cams curiosity
John is an incredible person, liked him immediately when we were working together in the early 90's. Yes, he is extremely busy as most of us are so I just text him what I need. If I need to talk with him, I send him a text that makes no sense and then he calls going WTF?
Heat is energy, energy is horsepower...but you gotta control the heat.
-Carl
-Carl