!970's Pro-Stock Camshaft Spec.'s
Moderator: Team
-
- Guru
- Posts: 1029
- Joined: Mon Sep 10, 2012 1:55 pm
- Location: Anaheim, CA
Re: !970's Pro-Stock Camshaft Spec.'s
The small block stuff was 106/108LSA and when the Big blocks hit the LSA went wide like Mike said. Teams used to outdo each other by having the slowest Idle speed.
-
- Vendor
- Posts: 3656
- Joined: Sat Feb 14, 2004 4:04 pm
- Location: Abbeville, LA
- Contact:
Re: !970's Pro-Stock Camshaft Spec.'s
in that Book , Jenkins was using mostly 109deg LSA
on the 331cid engines + 355 and 358 cid
-
- Guru
- Posts: 1575
- Joined: Mon Apr 04, 2011 8:54 pm
- Location: central Florida
Re: !970's Pro-Stock Camshaft Spec.'s
Hey Mike, there was a Roy Hill, it seems like he was the one who drove for the Petty Drag Race Entry from North Carolina . This would have been between appx. 1974 and 1984 is my guess ?? Mark H.
-
- Vendor
- Posts: 3656
- Joined: Sat Feb 14, 2004 4:04 pm
- Location: Abbeville, LA
- Contact:
Re: !970's Pro-Stock Camshaft Spec.'s
swampbuggy wrote: ↑Mon Jan 24, 2022 10:15 pm Hey Mike, there was a Roy Hill, it seems like he was the one who drove for the Petty Drag Race Entry from North Carolina . This would have been between appx. 1974 and 1984 is my guess ?? Mark H.
You do not have the required permissions to view the files attached to this post.
-
- HotPass
- Posts: 3462
- Joined: Sat Feb 23, 2013 5:42 pm
- Location:
Re: !970's Pro-Stock Camshaft Spec.'s
If those were with Harold's lobes, don't have too much crossover to a symmetrical profile, but you know thatmaxracesoftware wrote: ↑Mon Jan 24, 2022 5:45 pmin that Book , Jenkins was using mostly 109deg LSA
on the 331cid engines + 355 and 358 cid
Same goes for anyone's lobes / valve lift curve that isn't symmetrical.
-Bob
- Stan Weiss
- Vendor
- Posts: 4820
- Joined: Tue Feb 20, 2007 1:31 pm
- Location: Philadelphia, PA
- Contact:
Re: !970's Pro-Stock Camshaft Spec.'s
This is from the link I posted on page 1. The data was gotten with a degree wheel and a dial indicator at that time. The 320M is a single pattern cam while the 321 Roller is a dual pattern cam. The 320M was done when new. I got the 321 used. Both are asymmetrical.Stan Weiss wrote: ↑Wed Jan 19, 2022 11:12 pm Might want to take a look at this thread.
Early 70's modified or gasser camshafts
viewtopic.php?t=43881
Stan
Stan
I run this in the earlier 70's GK Flat tappet 320M 372L and this was before Brookshire was at GK.
CAM_______Lift______Opens___Closes__Duration
_________________Deg_BTDC__Deg_ABDC_____________Area
_________0.00600____95.00_|_143.33_|_418.33_|__39.34
_________0.01000____80.00_|_125.00_|_385.00_|__39.20
_________0.02000____53.33_|__95.71_|_329.05_|__38.72
_________0.04000____35.88_|__76.67_|_292.55_|__37.99
_________0.05000____30.00_|__70.00_|_280.00_|__37.99
_________0.10000____14.05_|__53.79_|_247.85_|__36.35
_________0.15000____-1.43_|__38.57_|_217.14_|__33.42
_________0.20000___-15.71_|__24.12_|_188.40_|__31.45
_________0.25000___-30.00_|__10.00_|_160.00_|__29.12
_________0.30000___-46.55_|__-6.67_|_126.78_|__23.53
_________0.35000___-70.00_|_-29.00_|__81.00_|__16.92
Stan
PS - This is GK Roller C1R321B 321R-434L 336R-424L from around that time. Thinking about it a little more this maybe more '74.
Intake
CAM_______Lift______Opens___Closes__Duration
_________________Deg_BTDC__Deg_ABDC_____________Area
_________0.00600____80.00_|_120.00_|_380.00_|__41.81
_________0.01000____70.00_|_110.00_|_360.00_|__41.73
_________0.02000____55.56_|__91.43_|_326.98_|__41.42
_________0.04000____39.44_|__75.00_|_294.44_|__40.69
_________0.05000____33.89_|__69.05_|_282.94_|__40.30
_________0.10000____14.14_|__48.86_|_243.00_|__38.42
_________0.15000____-0.51_|__34.72_|_214.21_|__36.35
_________0.20000___-13.17_|__22.14_|_188.97_|__34.37
_________0.25000___-25.95_|__10.00_|_164.05_|__31.98
_________0.30000___-38.75_|__-3.16_|_138.09_|__27.48
_________0.35000___-54.14_|_-17.74_|_108.12_|__22.59
_________0.40000___-74.74_|_-36.52_|__68.74_|__14.84
Exhaust
_________0.00600___149.67_|_127.00_|_456.67_|__43.58
_________0.01000___133.00_|_113.67_|_426.67_|__43.43
_________0.02000___103.00_|__77.00_|_360.00_|__42.97
_________0.04000____82.47_|__43.43_|_305.90_|__41.86
_________0.05000____77.21_|__36.47_|_293.68_|__41.47
_________0.10000____58.16_|__15.75_|_253.91_|__39.60
_________0.15000____43.56_|___0.89_|_224.44_|__38.19
_________0.20000____30.37_|_-11.37_|_199.00_|__35.52
_________0.25000____17.05_|_-24.62_|_172.43_|__31.67
_________0.30000_____3.00_|_-38.59_|_144.41_|__28.78
_________0.35000___-14.78_|_-55.00_|_110.22_|__22.08
_________0.40000___-40.08_|_-78.33_|__61.59_|__12.51
Stan Weiss/World Wide Enterprises
Offering Performance Software Since 1987
http://www.magneticlynx.com/carfor/carfor.htm
David Vizard & Stan Weiss' IOP / Flow / Induction Optimization Software
http://www.magneticlynx.com/DV
Offering Performance Software Since 1987
http://www.magneticlynx.com/carfor/carfor.htm
David Vizard & Stan Weiss' IOP / Flow / Induction Optimization Software
http://www.magneticlynx.com/DV
Re: !970's Pro-Stock Camshaft Spec.'s
I think that's the driver, but I think it was after 1985, but before 1990.swampbuggy wrote: ↑Mon Jan 24, 2022 10:15 pm Hey Mike, there was a Roy Hill, it seems like he was the one who drove for the Petty Drag Race Entry from North Carolina . This would have been between appx. 1974 and 1984 is my guess ?? Mark H.
Mike Jones
Jones Cam Designs
Denver, NC
jonescams@bellsouth.net
http://www.jonescams.com
Jones Cam Designs' HotPass Vendors Forum: viewforum.php?f=44
(704)489-2449
Jones Cam Designs
Denver, NC
jonescams@bellsouth.net
http://www.jonescams.com
Jones Cam Designs' HotPass Vendors Forum: viewforum.php?f=44
(704)489-2449
-
- Guru
- Posts: 1575
- Joined: Mon Apr 04, 2011 8:54 pm
- Location: central Florida
Re: !970's Pro-Stock Camshaft Spec.'s
Thanks to Larry for the Picture of the Roy Hill driven Mopar, and Thank you Mike ( CamKing ) and every body else who contributed to this thread, it was a dream back in time and was enjoyable. Mark H.
-
- Vendor
- Posts: 3656
- Joined: Sat Feb 14, 2004 4:04 pm
- Location: Abbeville, LA
- Contact:
Re: !970's Pro-Stock Camshaft Spec.'s
i just uploaded a full-size picture of Roy Hill's ProStockerswampbuggy wrote: ↑Wed Jan 26, 2022 6:53 am Thanks to Larry for the Picture of the Roy Hill driven Mopar, and Thank you Mike ( CamKing ) and every body else who contributed to this thread, it was a dream back in time and was enjoyable. Mark H.
i think i took this Pic at Houma,LA ( Southland Dragstrip )
click the + icon to see all the Pic
and it sure looks like Bill Jenkins in the Blue Valvoline Decal Shirt sitting in Roy Hill's Trailer )
Full-size image Link here : ( the orginal Scan is 3 times larger than this pic , probably need a 50" or 60" TV to fully see all of it )
https://i.postimg.cc/s34Ydp0B/Roy-Hill-Pro243-B.jpg
alternate Pic link on my Public Forum here :
https://www.maxracesoftwares.com/forum/ ... f=39&t=287
Re: !970's Pro-Stock Camshaft Spec.'s
You can thank those guys for their hard work and being the r&d through those early years that allows you to have the information and ready to go parts to go this fast so easy6.50camaro wrote: ↑Sat Jan 22, 2022 2:33 pm It's hard for me to really get the picture in my head that today my 422 flat top piston, single 4150 carb, powerglide, sbc 72 camaro is as fast as those 1st gen tunnel rammed,4 speed big block Pro stock cars that I went to see at a match race in the early 70's.
Re: !970's Pro-Stock Camshaft Spec.'s
Re Roy Hill; one saw him race once, the U.S. Pro Stock Open in either 1976 or 1977. He and his Duster weren't the fastest car that night, but he won, which was even cooler since I drove down to MIR w/ my friend in his immaculate 1971 Duster 340.swampbuggy wrote: ↑Wed Jan 26, 2022 6:53 am Thanks to Larry for the Picture of the Roy Hill driven Mopar, and Thank you Mike ( CamKing ) and every body else who contributed to this thread, it was a dream back in time and was enjoyable. Mark H.
Also found this a little while ago: http://competitionplus.com/drag-racing/ ... y-accident
If you scroll to the bottom of that article, there's a Legend of Drag Racing episode about him linked to it. I have no idea how old it is...
-
- Vendor
- Posts: 3656
- Joined: Sat Feb 14, 2004 4:04 pm
- Location: Abbeville, LA
- Contact:
Re: !970's Pro-Stock Camshaft Spec.'s
General Kinetics GK 321D Cam Lobe Profile :
full size Pics on my Public Forum here :
https://www.maxracesoftwares.com/forum/ ... f=28&t=288
full size Pics on my Public Forum here :
https://www.maxracesoftwares.com/forum/ ... f=28&t=288
You do not have the required permissions to view the files attached to this post.