Question for anyone running one of my Hydr Roller cams

[CamKing]

If you have run one of my hydr roller cams, and have had your engine on a dyno(chassis or engine), can you please list;
Engine make and CID:
Compression:
Cam specs or part#:
Max HP and RPM:
Max Torque and RPM:

I'm working on some new software.
Thanks in advance.

[Orr89rocz]

401” chevy sbc
9:1 compression AFR 195 eliminator heads
Jones HR 73353. 233/233 112 lsa .564”/.564”
Pump gas twin 60 mm t4 turbo street deal
Th400

Mustang dyno so not sure how accurate but
638 whp at 5300-5500 on 12.5 psi
1001 wtq but i dont recall the rpm

[DCal]

Sbc 401 cid
10.48:1
233/236 @.050, .583/.562 lift 109 cl in at 105
554 @ 6150, 531 tq @4900

[Warp Speed]

Can't really post that info (although I'm sure you can access it easy enough lol) but I'll brag on ya a bit.
Been 170 in the 1/8 with one!

[bob460]

Can't really post that info (although I'm sure you can access it easy enough lol) but I'll brag on ya a bit.
Been 170 in the 1/8 with one!

Oooofff what a tease

Must be 4.1s impressive .............what rpm you going with the hydraulic roller cam?

[Warp Speed]

Have been well over 8k with Mike's hydraulic cams.
9k+ in dohc configuration.

[CamKing]

Sbc 401 cid
10.48:1
233/236 @.050, .583/.562 lift 109 cl in at 105
554 @ 6150, 531 tq @4900

What heads ?

[1980RS]

Humm..., might need someone to grind me a cam for this junk peanut port engine some day.

[DCal]

Sbc 401 cid
10.48:1
233/236 @.050, .583/.562 lift 109 cl in at 105
554 @ 6150, 531 tq @4900

What heads ?

Brodix Track 1= flowed 312 @ .600. If ever it's not just for street I could get 600hp easily, but right now its just what I needed, Thanks

[swampbuggy]

Warp Speed: Would that impressive pass have been in that Classic Nova that i have seen ? Mark H.

[Warp Speed]

Warp Speed: Would that impressive pass have been in that Classic Nova that i have seen ? Mark H.

No, that would be a Jones solid roller in it, and it's been 194 in the 1/8th @ 3350lbs on gas!

[swampbuggy]

And would that be the R0-7 that you have been working on ? The 194 / 1/8 mi. Thanks Swampbuggy .

[Warp Speed]

No, not mine! Lol I thought you were talking about an orange one with a twin turbo BBC.

[DCal]

Can we not get more responses for Camking, you know, the guy that gives us free advice and suggests grinds for us? You say he's going to recommend HIS grinds -of course he will, he's in business! But it will be in the hunt for sure, so lets feed him some more info and make it even better.

[Bill Chase]

Can we not get more responses for Camking, you know, the guy that gives us free advice and suggests grinds for us? You say he's going to recommend HIS grinds -of course he will, he's in business! But it will be in the hunt for sure, so lets feed him some more info and make it even better.

Actually, if you search or read many old posts here, if a guy has a cam (or is looking at a competitors cam) that is close Mike will say so. More than a few posts where he has said what he has to offer would be a minimal gain compared to what the poster has, or his cam would not be cost effective until heads or something else are changed. He definately doesnt just try to sell his cam every time. and if the cam the guy has will do it, he says that too. The fact that he takes the time to answer questions for knuckleheads like me is amazing. Makes ya wonder how he has time to work, have a family etc.