Where can I get these?

General engine tech -- Drag Racing to Circle Track

Moderator: Team

Post Reply
ArizonaGuy
Member
Member
Posts: 138
Joined: Thu Dec 24, 2020 4:25 pm
Location: Phoenix, Arizona

Where can I get these?

Post by ArizonaGuy »

3/8 barb necked down to 1/4. I’ve looked around a good bit, no luck so far. See yellow circle
86FF5127-0457-4A28-B595-23C86C9AFD8C.jpeg
You do not have the required permissions to view the files attached to this post.
ArizonaGuy
Member
Member
Posts: 138
Joined: Thu Dec 24, 2020 4:25 pm
Location: Phoenix, Arizona

Re: Where can I get these?

Post by ArizonaGuy »

A couple of options I can probably make work (with a little rubbing, but that’s ok).
450FBCC3-D0E8-4BB0-A9BD-232D11666D0D.jpeg
19E62ABE-0CA9-42CB-B9A8-191F61C0A1A6.jpeg
You do not have the required permissions to view the files attached to this post.
ArizonaGuy
Member
Member
Posts: 138
Joined: Thu Dec 24, 2020 4:25 pm
Location: Phoenix, Arizona

Re: Where can I get these?

Post by ArizonaGuy »

But I’d rather have this (yellow arrow). 3/8 flare barb to 1/4 press fit tube. The throttle body I want to put it in doesn’t have much meat to work with.

690195A0-5F6C-40D5-BECC-54699E7BA566.jpeg
You do not have the required permissions to view the files attached to this post.
HQM383
HotPass
HotPass
Posts: 1021
Joined: Sun Sep 12, 2021 7:25 am
Location: Geelong, Vic

Re: Where can I get these?

Post by HQM383 »

Might be worth giving these guys a call if you haven't already

https://allcarbs.com/?v=920f83e594a1

https://blp.com/cart/index.php?main_page=index&cPath=65
I’m a Street/Strip guy..... like to think outside the quadrilateral parallelogram.
ArizonaGuy
Member
Member
Posts: 138
Joined: Thu Dec 24, 2020 4:25 pm
Location: Phoenix, Arizona

Re: Where can I get these?

Post by ArizonaGuy »

HQM383 wrote: Tue Aug 09, 2022 6:12 pm Might be worth giving these guys a call if you haven't already

https://allcarbs.com/?v=920f83e594a1

https://blp.com/cart/index.php?main_page=index&cPath=65
I haven’t yet, but I will. Thanks 👍
hoodeng
HotPass
HotPass
Posts: 1092
Joined: Sat Mar 04, 2017 6:53 pm
Location: South Australia

Re: Where can I get these?

Post by hoodeng »

Turn down the barbed ones to what you want.
ArizonaGuy
Member
Member
Posts: 138
Joined: Thu Dec 24, 2020 4:25 pm
Location: Phoenix, Arizona

Re: Where can I get these?

Post by ArizonaGuy »

hoodeng wrote: Tue Aug 09, 2022 7:36 pm Turn down the barbed ones to what you want.
They’re pretty thin, but it’s worth a shot. I’ll try that too.
Walter R. Malik
Guru
Guru
Posts: 6355
Joined: Tue Jul 24, 2012 11:15 am
Location: Roseville, Michigan (just north of Detroit)
Contact:

Re: Where can I get these?

Post by Walter R. Malik »

ArizonaGuy wrote: Tue Aug 09, 2022 3:45 pm 3/8 barb necked down to 1/4. I’ve looked around a good bit, no luck so far. See yellow circle

86FF5127-0457-4A28-B595-23C86C9AFD8C.jpeg
I have several out there which I have made.
Get a proper 3/8" tube and a 1/4" tube with a very short collar of 5/16" tube ... using some silver solder with a natural gas torch, fuse them together.
http://www.rmcompetition.com
Specialty engine building at its finest.
hoodeng
HotPass
HotPass
Posts: 1092
Joined: Sat Mar 04, 2017 6:53 pm
Location: South Australia

Re: Where can I get these?

Post by hoodeng »

If you go down Walter's bundy tube route, you could make the 3/8" end barb with a brake tube flaring tool by only doing the first step.
1980RS
Guru
Guru
Posts: 1636
Joined: Thu Oct 13, 2016 10:03 am
Location:

Re: Where can I get these?

Post by 1980RS »

I would think Allstate Carburetor would have those.
Post Reply