Small Block Chevy Engines and Parts + T-56 Transmissions
Posted: Tue Oct 14, 2014 2:36 am
Having retired, it is time to inventory and put up for sale items remaining from past projects. All parts are new unless noted otherwise.
If interested, please send PM. I am located NW of Houston, Texas. Reasonable offers considered. Prices listed are negotiable.
* Will ship smaller parts and split shipping cost within lower 48 states...... Payment by US Postal Money Order accepted.
* Larger parts to be picked up in person, cash on receipt...... No checks, MOs nor credit cards.
All sales are final......
Individual parts prices for parts to build 427 cu.in. (7 litre) Chevy small block (all parts new, stored inside since 1998)......
$1,700 - General Motors Performance Parts 400 Sportsman block, Bowtie siamesed bore casting with 350 main size......
$500 - Custom Wiseco forged pistons (dished), 4.125" bore size with 1.170" comp.height, 1/16" rings, yields 9.44:1 comp ratio with 65cc chamber at 0.046" quench......
$400 - Eagle 3D 4340 H-beam stroker profile rods (5.850" length)......
$500 - 4" stroke COLA 4340 forged crank, 350 main and journal size......
I would prefer to sell the balanced rotating assembly (crank, rods and pistons) as a unit, either with or without the GMPP block (reciprocating assembly has been internally balanced using Mallory metal).
$1,400 - rotating assembly
$1,700 - block
Note: Will accept $2,800.00 for GMPP block and rotating assembly as a package deal (will include moly file fit rings and bearing set at no additional charge)
New heads, intake manifolds and exhaust manifolds for small block Chevy......
$2,800 - Victor Jr. heads with full portwork by Mondello, intake ports matched to 1209 gasket size, 65cc chambers, 2.08" /1.60" valves. Intake side flows 306 cfm @ 0.525" lift per Mondello.
$1,350 - GMPP Fast Burn aluminum heads, 210cc intake ports, 62cc chambers, lightweight 2.0" / 1.55" LT4 valves
$180 - Edelbrock Performer RPM intake for Vortec & Fast Burn heads (removed from new GMPP crate engine)
$180 - GM crossram intake base for 1st design GM 229 V-6 Bowtie racing heads. With very few mods to intake, this intake can be made to fit '85 - '94 4.3 litre V-6 production heads as well. Consists of base only - You will need make a top plate to fit the carburettor(s) you wish to run.
$180 - Sanderson QP1000 cast iron exhaust manifolds. Special ordered with both sides having outlet centered. Note: These are both passenger side manifolds. They tuck in very close to the block and on the drivers side, there is a clearance issue with one of the raised bosses cast into 1958 and later blocks for side engine mounts. As such, either the boss must be ground about 1/4" for clearance and '55 - '57 front mounts used...... Or spacers similar to those used to adapt Stahl headers may be fitted between drivers side head and manifold to gain additional clearance so side engine mounts may be used.
New camshaft with lifters and roller rocker set......
$235 - UltraDyne custom flat tappet solid lifter cam and lifters (252 degrees duration @ 0.050" lift intake and exhaust, 0.525" lift, ground on 110 degree LSA, reduced base circle of 1.10", Pro-55 core)
$215 - GMPP self-guiding roller rocker arms (set of 16 special ordered with 8 having 1.6 ratio and 8 having 1.5 ratio) Note: self-guiding rocker arms will work only with hydraulic lifter cams. Do not use these type rockers with solid lifter cams.
Used intakes......
$530 - Hilborn 265 C 8J fuel injection intake with 2-3/16" throttle blades for small block Chevy. Manifold with throttle shafts and blades and some linkage. No ram tubes, injectors nor pump, etc. Just manifold and throttle blades with some linkage. Shafts, throttle blades and linkage move freely. Intake is in very good condition. Excellent candidate for EFI conversion.
$300 - Offenhauser #5253 dual quad 360 degree intake for small block Chevy (polished aluminum finish, very nice looking intake)
New transmissions, bellhousings, flywheels, clutches......
$2,400 - New T-56 Borg Warner 'aftermarket' 6-speed trans. This will bolt up to standard GM bellhousing and has mechanical speedo gear and cable connection for older vehicles.
$3,000 - New T-56 Borg Warner 6-speed production trans, OEM for '93 - '95 Camaro or Firebird with 305 or 350 engine. Price includes new GM bellhousing, new GM flywheel, new GM '94 Camaro hydraulic master and slave cylinder and new Center Force (pull type) clutch upgrade for this transmission.
(Both of these transmissions were bought in late '90s before Tremec (Mexico) acquired Borg Warner Transmission Division)
New 350 Chevy L31 Vortec engine with performance upgrades......
$2,500 - New (still strapped to shipping pallet) 1998 L31 Vortec 350 crate engine. This was sourced from Sallee Chevrolet in 1998. Sold as their 'Xtreme 350 4X4' crate engine. Has Comp Cams RV roller cam upgrade, ZZ4 timing gears and chain, Edelbrock Performer RPM intake, and new GM HEI distributor which I had recurved by Dave Ray to suit this engine. I have pulled the L31 heads, which have been sold. Price lowered to reflect this.
Have a set of new GMPP Fastburn heads for sale as well. If you are interested in a package deal, will sell crate engine (less L31 heads) and include Fastburn heads for $3,750.
Best regards and thanks for looking through the listing,
Harry
If interested, please send PM. I am located NW of Houston, Texas. Reasonable offers considered. Prices listed are negotiable.
* Will ship smaller parts and split shipping cost within lower 48 states...... Payment by US Postal Money Order accepted.
* Larger parts to be picked up in person, cash on receipt...... No checks, MOs nor credit cards.
All sales are final......
Individual parts prices for parts to build 427 cu.in. (7 litre) Chevy small block (all parts new, stored inside since 1998)......
$1,700 - General Motors Performance Parts 400 Sportsman block, Bowtie siamesed bore casting with 350 main size......
$500 - Custom Wiseco forged pistons (dished), 4.125" bore size with 1.170" comp.height, 1/16" rings, yields 9.44:1 comp ratio with 65cc chamber at 0.046" quench......
$400 - Eagle 3D 4340 H-beam stroker profile rods (5.850" length)......
$500 - 4" stroke COLA 4340 forged crank, 350 main and journal size......
I would prefer to sell the balanced rotating assembly (crank, rods and pistons) as a unit, either with or without the GMPP block (reciprocating assembly has been internally balanced using Mallory metal).
$1,400 - rotating assembly
$1,700 - block
Note: Will accept $2,800.00 for GMPP block and rotating assembly as a package deal (will include moly file fit rings and bearing set at no additional charge)
New heads, intake manifolds and exhaust manifolds for small block Chevy......
$2,800 - Victor Jr. heads with full portwork by Mondello, intake ports matched to 1209 gasket size, 65cc chambers, 2.08" /1.60" valves. Intake side flows 306 cfm @ 0.525" lift per Mondello.
$1,350 - GMPP Fast Burn aluminum heads, 210cc intake ports, 62cc chambers, lightweight 2.0" / 1.55" LT4 valves
$180 - Edelbrock Performer RPM intake for Vortec & Fast Burn heads (removed from new GMPP crate engine)
$180 - GM crossram intake base for 1st design GM 229 V-6 Bowtie racing heads. With very few mods to intake, this intake can be made to fit '85 - '94 4.3 litre V-6 production heads as well. Consists of base only - You will need make a top plate to fit the carburettor(s) you wish to run.
$180 - Sanderson QP1000 cast iron exhaust manifolds. Special ordered with both sides having outlet centered. Note: These are both passenger side manifolds. They tuck in very close to the block and on the drivers side, there is a clearance issue with one of the raised bosses cast into 1958 and later blocks for side engine mounts. As such, either the boss must be ground about 1/4" for clearance and '55 - '57 front mounts used...... Or spacers similar to those used to adapt Stahl headers may be fitted between drivers side head and manifold to gain additional clearance so side engine mounts may be used.
New camshaft with lifters and roller rocker set......
$235 - UltraDyne custom flat tappet solid lifter cam and lifters (252 degrees duration @ 0.050" lift intake and exhaust, 0.525" lift, ground on 110 degree LSA, reduced base circle of 1.10", Pro-55 core)
$215 - GMPP self-guiding roller rocker arms (set of 16 special ordered with 8 having 1.6 ratio and 8 having 1.5 ratio) Note: self-guiding rocker arms will work only with hydraulic lifter cams. Do not use these type rockers with solid lifter cams.
Used intakes......
$530 - Hilborn 265 C 8J fuel injection intake with 2-3/16" throttle blades for small block Chevy. Manifold with throttle shafts and blades and some linkage. No ram tubes, injectors nor pump, etc. Just manifold and throttle blades with some linkage. Shafts, throttle blades and linkage move freely. Intake is in very good condition. Excellent candidate for EFI conversion.
$300 - Offenhauser #5253 dual quad 360 degree intake for small block Chevy (polished aluminum finish, very nice looking intake)
New transmissions, bellhousings, flywheels, clutches......
$2,400 - New T-56 Borg Warner 'aftermarket' 6-speed trans. This will bolt up to standard GM bellhousing and has mechanical speedo gear and cable connection for older vehicles.
$3,000 - New T-56 Borg Warner 6-speed production trans, OEM for '93 - '95 Camaro or Firebird with 305 or 350 engine. Price includes new GM bellhousing, new GM flywheel, new GM '94 Camaro hydraulic master and slave cylinder and new Center Force (pull type) clutch upgrade for this transmission.
(Both of these transmissions were bought in late '90s before Tremec (Mexico) acquired Borg Warner Transmission Division)
New 350 Chevy L31 Vortec engine with performance upgrades......
$2,500 - New (still strapped to shipping pallet) 1998 L31 Vortec 350 crate engine. This was sourced from Sallee Chevrolet in 1998. Sold as their 'Xtreme 350 4X4' crate engine. Has Comp Cams RV roller cam upgrade, ZZ4 timing gears and chain, Edelbrock Performer RPM intake, and new GM HEI distributor which I had recurved by Dave Ray to suit this engine. I have pulled the L31 heads, which have been sold. Price lowered to reflect this.
Have a set of new GMPP Fastburn heads for sale as well. If you are interested in a package deal, will sell crate engine (less L31 heads) and include Fastburn heads for $3,750.
Best regards and thanks for looking through the listing,
Harry