TorqueMaster cam program update
Moderator: David Vizard
Re: TorqueMaster cam program update
i shall wait patiently for this to be applicable to generic (i.e any) cylinder head
-
- Guru
- Posts: 1787
- Joined: Thu Jan 15, 2015 12:19 pm
- Location:
Re: TorqueMaster cam program update
Digger,
I appreciate your patience here. My next move is to make this along with the flow bench program 4 valve friendly. It's a lot of work and I am still recovering from my brain surgery so I am not in the best of shape to handle my current work overload.
But I will get there!!!!
DV
David Vizard Small Group Performance Seminars - held about every 2 months. My shop or yours. Contact for seminar deails - davidvizardseminar@gmail.com for details.
- Stan Weiss
- Vendor
- Posts: 4821
- Joined: Tue Feb 20, 2007 1:31 pm
- Location: Philadelphia, PA
- Contact:
Re: TorqueMaster cam program update
The other 14 Day has expired and will no run. This is the install package for a new 14 Day version of TMC. It is in a zipped file that requires a password to Unzip. Please PM me to get the password. If it turns out to matter it was zipped with 7zFM.
Stan
Stan
Stan Weiss/World Wide Enterprises
Offering Performance Software Since 1987
http://www.magneticlynx.com/carfor/carfor.htm
David Vizard & Stan Weiss' IOP / Flow / Induction Optimization Software
http://www.magneticlynx.com/DV
Offering Performance Software Since 1987
http://www.magneticlynx.com/carfor/carfor.htm
David Vizard & Stan Weiss' IOP / Flow / Induction Optimization Software
http://www.magneticlynx.com/DV
- Stan Weiss
- Vendor
- Posts: 4821
- Joined: Tue Feb 20, 2007 1:31 pm
- Location: Philadelphia, PA
- Contact:
Re: TorqueMaster cam program update
This is a new version of the install package for the 14 Day version of TMC. What is new is that this has a preliminary version for Pontiac (HFT, HRT, SRT). If you have tried a previous version this version will still. It is in a zipped file that requires a password to Unzip. Please PM me to get the password. If it turns out to matter it was zipped with 7zFM.
Stan
Stan
Stan Weiss/World Wide Enterprises
Offering Performance Software Since 1987
http://www.magneticlynx.com/carfor/carfor.htm
David Vizard & Stan Weiss' IOP / Flow / Induction Optimization Software
http://www.magneticlynx.com/DV
Offering Performance Software Since 1987
http://www.magneticlynx.com/carfor/carfor.htm
David Vizard & Stan Weiss' IOP / Flow / Induction Optimization Software
http://www.magneticlynx.com/DV
- Stan Weiss
- Vendor
- Posts: 4821
- Joined: Tue Feb 20, 2007 1:31 pm
- Location: Philadelphia, PA
- Contact:
Re: TorqueMaster cam program update
I know some of you coming in here and reading this thread are saying they added Pontiac? The answer is yes we added Pontiac because I like Pontiac. I want to thank Mike / Pastry_Chef for all of his help during the development of the Pontiac version. I am, although very slowly working on a BBC SRT version. I have no idea of any time frame when it will even be ready for someone to "BETA" test.
Stan
Stan
You do not have the required permissions to view the files attached to this post.
Stan Weiss/World Wide Enterprises
Offering Performance Software Since 1987
http://www.magneticlynx.com/carfor/carfor.htm
David Vizard & Stan Weiss' IOP / Flow / Induction Optimization Software
http://www.magneticlynx.com/DV
Offering Performance Software Since 1987
http://www.magneticlynx.com/carfor/carfor.htm
David Vizard & Stan Weiss' IOP / Flow / Induction Optimization Software
http://www.magneticlynx.com/DV
-
- Pro
- Posts: 235
- Joined: Wed Jul 07, 2004 10:06 pm
- Location: Ottawa, Canada
Re: TorqueMaster cam program update
How does the cam know what logo is stamped on the block ?Stan Weiss wrote: ↑Thu Jul 09, 2020 11:00 am I know some of you coming in here and reading this thread are saying they added Pontiac? The answer is yes we added Pontiac because I like Pontiac. I want to thank Mike / Pastry_Chef for all of his help during the development of the Pontiac version. I am, although very slowly working on a BBC SRT version. I have no idea of any time frame when it will even be ready for someone to "BETA" test.
Stan
tmc_bbc.gif
Mike Jones
Jones Cam Designs
Denver, NC
jonescams@bellsouth.net
http://www.jonescams.com
Jones Cam Designs' HotPass Vendors Forum: viewforum.php?f=44
(704)489-2449
Jones Cam Designs
Denver, NC
jonescams@bellsouth.net
http://www.jonescams.com
Jones Cam Designs' HotPass Vendors Forum: viewforum.php?f=44
(704)489-2449
- Stan Weiss
- Vendor
- Posts: 4821
- Joined: Tue Feb 20, 2007 1:31 pm
- Location: Philadelphia, PA
- Contact:
Re: TorqueMaster cam program update
If you get this error." Run-time error "429": ActiveX component can't create object" error.
Please download and try this version if you get that error and let me know if it fixes things. Please note that anyone downloading the program for the first time should download the above version first. This zip file uses the same password as you were giving before.
Stan
Please download and try this version if you get that error and let me know if it fixes things. Please note that anyone downloading the program for the first time should download the above version first. This zip file uses the same password as you were giving before.
Stan
You do not have the required permissions to view the files attached to this post.
Stan Weiss/World Wide Enterprises
Offering Performance Software Since 1987
http://www.magneticlynx.com/carfor/carfor.htm
David Vizard & Stan Weiss' IOP / Flow / Induction Optimization Software
http://www.magneticlynx.com/DV
Offering Performance Software Since 1987
http://www.magneticlynx.com/carfor/carfor.htm
David Vizard & Stan Weiss' IOP / Flow / Induction Optimization Software
http://www.magneticlynx.com/DV
- Stan Weiss
- Vendor
- Posts: 4821
- Joined: Tue Feb 20, 2007 1:31 pm
- Location: Philadelphia, PA
- Contact:
Re: TorqueMaster cam program update
Mike,CamKing wrote: ↑Fri Jul 10, 2020 1:45 pmHow does the cam know what logo is stamped on the block ?Stan Weiss wrote: ↑Thu Jul 09, 2020 11:00 am I know some of you coming in here and reading this thread are saying they added Pontiac? The answer is yes we added Pontiac because I like Pontiac. I want to thank Mike / Pastry_Chef for all of his help during the development of the Pontiac version. I am, although very slowly working on a BBC SRT version. I have no idea of any time frame when it will even be ready for someone to "BETA" test.
Stan
tmc_bbc.gif
The program specs / lets you select most engine components. Hard to fit a Pontiac crankshaft into a SBF.
Stan
Stan Weiss/World Wide Enterprises
Offering Performance Software Since 1987
http://www.magneticlynx.com/carfor/carfor.htm
David Vizard & Stan Weiss' IOP / Flow / Induction Optimization Software
http://www.magneticlynx.com/DV
Offering Performance Software Since 1987
http://www.magneticlynx.com/carfor/carfor.htm
David Vizard & Stan Weiss' IOP / Flow / Induction Optimization Software
http://www.magneticlynx.com/DV
Re: TorqueMaster cam program update
Does it give you the part# of the crank, or just the stroke?Stan Weiss wrote: ↑Fri Jul 10, 2020 2:47 pmMike,CamKing wrote: ↑Fri Jul 10, 2020 1:45 pmHow does the cam know what logo is stamped on the block ?Stan Weiss wrote: ↑Thu Jul 09, 2020 11:00 am I know some of you coming in here and reading this thread are saying they added Pontiac? The answer is yes we added Pontiac because I like Pontiac. I want to thank Mike / Pastry_Chef for all of his help during the development of the Pontiac version. I am, although very slowly working on a BBC SRT version. I have no idea of any time frame when it will even be ready for someone to "BETA" test.
Stan
tmc_bbc.gif
The program specs / lets you select most engine components. Hard to fit a Pontiac crankshaft into a SBF.
Stan
Mike Jones
Jones Cam Designs
Denver, NC
jonescams@bellsouth.net
http://www.jonescams.com
Jones Cam Designs' HotPass Vendors Forum: viewforum.php?f=44
(704)489-2449
Jones Cam Designs
Denver, NC
jonescams@bellsouth.net
http://www.jonescams.com
Jones Cam Designs' HotPass Vendors Forum: viewforum.php?f=44
(704)489-2449
- Stan Weiss
- Vendor
- Posts: 4821
- Joined: Tue Feb 20, 2007 1:31 pm
- Location: Philadelphia, PA
- Contact:
Re: TorqueMaster cam program update
MikeCamKing wrote: ↑Fri Jul 10, 2020 2:55 pmDoes it give you the part# of the crank, or just the stroke?Stan Weiss wrote: ↑Fri Jul 10, 2020 2:47 pmMike,
The program specs / lets you select most engine components. Hard to fit a Pontiac crankshaft into a SBF.
Stan
There are a series of Excell spreadsheet which have a number of components. If I was doing my part better it would have part #, stroke, cast or forged for the Pontiac which main journal size 3" or 3.25".
This report is an example of a report of the shopping cart type function. Note they were random selections just for testing
Stan
You do not have the required permissions to view the files attached to this post.
Stan Weiss/World Wide Enterprises
Offering Performance Software Since 1987
http://www.magneticlynx.com/carfor/carfor.htm
David Vizard & Stan Weiss' IOP / Flow / Induction Optimization Software
http://www.magneticlynx.com/DV
Offering Performance Software Since 1987
http://www.magneticlynx.com/carfor/carfor.htm
David Vizard & Stan Weiss' IOP / Flow / Induction Optimization Software
http://www.magneticlynx.com/DV
-
- New Member
- Posts: 17
- Joined: Fri Jun 19, 2020 4:11 pm
- Location:
Re: TorqueMaster cam program update
For the crank spec on SBF Windsor engines, the field should allow the 4.25 stroke cranks. Right now the max entry is 4.2
I fudged my inputs from my actual spec of 4.25 crank and 4.155 bore, to 4.2 crank and 4.18 bore to arrive at the right Cu in of 461.
Not sure if fudging the bore and stroke has an effect on the results?
Thanks!
I fudged my inputs from my actual spec of 4.25 crank and 4.155 bore, to 4.2 crank and 4.18 bore to arrive at the right Cu in of 461.
Not sure if fudging the bore and stroke has an effect on the results?
Thanks!
- Stan Weiss
- Vendor
- Posts: 4821
- Joined: Tue Feb 20, 2007 1:31 pm
- Location: Philadelphia, PA
- Contact:
Re: TorqueMaster cam program update
I have not run your numbers so do not know what the results will be. But the program does know the difference. I have changed the program to let you enter a 4.25" stroke for the SBF.68fastback wrote: ↑Wed Jul 15, 2020 2:26 pm For the crank spec on SBF Windsor engines, the field should allow the 4.25 stroke cranks. Right now the max entry is 4.2
I fudged my inputs from my actual spec of 4.25 crank and 4.155 bore, to 4.2 crank and 4.18 bore to arrive at the right Cu in of 461.
Not sure if fudging the bore and stroke has an effect on the results?
Thanks!
This is a new version of the install package. While it says 14 Day version of TMC it is actually a 30 Day version. So if you have the 14 version up and running it should give another 16 days. If you have tried a previous version this version will still work. It is in a zipped file that requires a password to Unzip. It uses the same password as the previous version if you now have TMC running. Please PM me to get the password. If it turns out to matter it was zipped with 7zFM.
Stan
Stan Weiss/World Wide Enterprises
Offering Performance Software Since 1987
http://www.magneticlynx.com/carfor/carfor.htm
David Vizard & Stan Weiss' IOP / Flow / Induction Optimization Software
http://www.magneticlynx.com/DV
Offering Performance Software Since 1987
http://www.magneticlynx.com/carfor/carfor.htm
David Vizard & Stan Weiss' IOP / Flow / Induction Optimization Software
http://www.magneticlynx.com/DV
-
- New Member
- Posts: 17
- Joined: Fri Jun 19, 2020 4:11 pm
- Location:
-
- New Member
- Posts: 11
- Joined: Fri Aug 07, 2020 11:37 pm
- Location: Nashville, IN, USA
Re: TorqueMaster cam program update
I'm getting an error every time I try to download the zip file. Any thoughts?
Also, assuming I can get this resolved, anyone know the "Induction Length" that should be used for a Super Victor EFI (29245) manifold?
Thanks, Damon
Also, assuming I can get this resolved, anyone know the "Induction Length" that should be used for a Super Victor EFI (29245) manifold?
Thanks, Damon
You do not have the required permissions to view the files attached to this post.